Professional Ramp Soak Temperature Controller Kiln SSR Kit Ceramic Thermocouple

Professional Ramp Soak Temperature Controller Kiln SSR Kit Ceramic Thermocouple
Professional Ramp Soak Temperature Controller Kiln SSR Kit Ceramic Thermocouple
Professional Ramp Soak Temperature Controller Kiln SSR Kit Ceramic Thermocouple
Professional Ramp Soak Temperature Controller Kiln SSR Kit Ceramic Thermocouple

Professional Ramp Soak Temperature Controller Kiln SSR Kit Ceramic Thermocouple
A Complete Applicable Package of Programable Digital PID Temperature Controller Ramp and Soak , Kiln Probe Thermocouple/Sensor & Solid State Relay (SSR) and Heatsink. All products are 100% Brand new, High performance and Top quality. Controller comes in Box with MANUAL. Programmable Digital PID Temperature Controller Ramp and Soak with 50 Segments and SSR Output. A length-adjustable Kiln Thermocouple with 6 pcs Ceramic insulator + Ceramic Terminal/Mountung block + 1m Wire Extension. Solid State Relay (40A), 24-240V AC. Heat Sink (80 x 50 x 50 mm). Dual Digital PID Temperature Programmable (Ramp & Soak) Controller with SSR output and universal type input. Use this Ramp & Soak PID Programmable Controller when you wish to precisely control the temperature of a kiln/heater on certain timely cycles. Can be programmed for multiple profiles up to 50 segments. 100% Brand new in Box with MANUAL , High performance and Top quality. Kiln, Oven, Furnace and etc. High accuracy 0.2%FS. Can have several different programs. Up to 50 segments. Be able to run/stop/pause/jump the program. Built-in Switching Power Supply. Auto/Manual control switch from front panel. Configurable time-dominate or value-dominate controls. Up to 50 segments available for a program. 200 to 1800 °C (depends on input type). Be able to program different patterns with different segments. Thermocouple: (K, S, E, J, T, B, N) RTD: (Cu50, PT100). Linear Voltage and current:0-5V, 1-5V, 0-1V, 0-100mV, 0-20mV, 0-60mV, 0.2-1V(100-500mV), -20 -+20mV(0-10V) -5V- +5V(0-50V), -100 – +100mV(2-10V) Linear Resistor:0-80 Ohm, 0-400 Ohm. Voltage pulse to drive SSR. Less than 0.5S (configurable). 0.2%FS+- 0.1C(Cu50 cooper resistor compensation or ice point compensation) 0.2%FS+0.2C (TC input and internal compensation). Less than 0.01%FS. C Typical value is 50ppm/. C or 0.1. Cautomatically change to 1. C when the temperature is higher than 999. Dual line – four digit – LED display. Configurable for all inputs. AI MPT with auto tuning, adopting fuzzy logic PID algorithm. Auto/manual bump less transfer from front panel. Auto-tuning and manual tuning available. Absolute value high limit, Absolute value low limit, Deviation high limit alarm, Deviation low limit alarm. In some occasions, for example, in the heating process, when the alarm is set to as low deviation alarm, right after the power is turned on, the alarm will be triggered but there is no problem in the system, the alarm block function can solve this problem. In some particular application, 100% output ratio is not allowed when the power just turned on; soft start function is a great feature to solve this problem. Available, as feed of PLC or indicator or paperless recorder. High Temperature Kiln Thermocouple. 1 A Ceramic Mounting Block. 2 1m (3.3 ft) wire extension with a Flat Pin (Miniature) connector at the end. Its Flat Pin connector can be connected dierectly to Digital Thermometers. By removing its Flat Pin, it can also be connected to Temperature Controllers. This heavy duty Type K Kiln probe Thermocouple, with 6 Pcs Ceramic Insulator gives you the UNIQUE option of adjusting the probe length (by bending it) to your exact requirement. It can measure up to 2372 °F. This high temperature 8 gauge kiln probe comes in 7.5 inch length. The length of this thermocouple is measured by the number of 1 inch long ceramics. Some extra length is added for connections. You can adjust the length of this thermocouple by bending the probe/thread at installation. 58 to 2372 °F (-50 to 1300 °C). 3.2 mm (0.13 inch). 190 mm (7.5 inch). 150 mm (6.0 inch). Oval shape: L=12.3 mm & W=10mm (L 0.5 & W 0.4). 6 x (1 inch Pcs) Ceramic Tube. Solid State Relay (SSR). 24 – 240V AC. 3 x 2 x 2 (80 x 50 x 50 mm). 0.22 lb (98 gr). We offer different packages by combining a wide range of Controllers, SSRs, Thermocouples & Heat Sinks. You name your inquiry, we produce it for you. “Thanks for taking time and observing this ad”. The item “Professional Ramp Soak Temperature Controller Kiln SSR Kit Ceramic Thermocouple” is in sale since Tuesday, April 09, 2013. This item is in the category “Consumer Electronics\Wholesale Lots\Other Consumer Electronic Lots”. The seller is “rogersdini” and is located in Ontario. This item can be shipped worldwide.
Professional Ramp Soak Temperature Controller Kiln SSR Kit Ceramic Thermocouple